Glossary
Short definitions of SPC, statistics and Lean Six Sigma terms.
- Alpha (α)
- The risk of a false alarm you accept in a test, usually 0.05.
- ANOVA
- Analysis of variance: tests whether the means of several groups differ.
- AQL
- Acceptable quality level: the worst average quality accepted by a sampling plan.
- Attribute data
- Counts or pass/fail results rather than measurements.
- B10 life
- The time by which 10% of units are expected to fail.
- Baseline
- A known good period whose readings set the control limits.
- Bias
- The average difference between a gauge's readings and the true value.
- Black Belt
- A full-time Six Sigma project leader.
- Capability
- How well a stable process fits inside its tolerance.
- Center line
- The average plotted on a control chart.
- Common cause
- The everyday random variation built into a process.
- Confidence interval
- A range that contains the true value with a stated confidence, such as 95%.
- Control limits
- Lines 3 sigma either side of the center line, calculated from the data. They show how far a stable process normally strays.
- Cp
- Tolerance width divided by six within-sigma: potential capability if centered.
- Cpk
- Distance from the mean to the nearer spec limit divided by three within-sigma: actual capability.
- Cpm
- Capability index that penalizes distance from the target.
- CTQ
- Critical to quality: a measurable characteristic that matters to the customer.
- CUSUM
- Cumulative sum chart: running totals of deviations from target, for small, lasting shifts.
- Defect / defective
- A defect is a flaw; a defective is an item with one or more flaws that fails.
- DMAIC
- Define, Measure, Analyze, Improve, Control.
- DNOM
- Deviation from nominal: a short-run chart plotting each part's distance from its own nominal.
- DOE
- Design of experiments: changing inputs in a planned pattern to measure their effects.
- DPMO
- Defects per million opportunities.
- DPMO / PPM
- Defects per million opportunities / parts per million.
- EWMA
- Exponentially weighted moving average chart: a smoothed line that catches small, lasting shifts.
- EWMA
- Exponentially weighted moving average chart.
- FMEA
- Failure mode and effects analysis.
- FPY
- First pass yield: share of units that pass a step the first time.
- Gage R&R
- A study of measurement error: repeatability (the gauge) and reproducibility (the people).
- Histogram
- Bars showing how many readings fall in each size range.
- I-MR chart
- Individuals and moving range chart, for one reading at a time.
- In control / stable
- Showing only common-cause variation: predictable.
- Kaizen
- Continuous improvement in small steps.
- Kappa
- Agreement beyond chance between inspectors: 1 is perfect, 0 is chance.
- Lead time
- Time from order to delivery, or from start to finish of a process.
- LSL / USL
- Lower and upper specification limits, from the drawing.
- Mean
- The average.
- Moving range
- The difference between a reading and the one before it.
- ndc
- Number of distinct categories a gauge can separate parts into; 5 or more is needed.
- Normal distribution
- The symmetric bell-shaped curve many measurements follow.
- OEE
- Overall equipment effectiveness: availability × performance × quality.
- Out of control
- Breaking one of the alarm rules: a sign of a special cause.
- p-value
- The chance of seeing a result at least this extreme if nothing were really going on. Small (below 0.05) means probably real.
- Pareto
- Categories sorted from most to least frequent, with a running total.
- Phase
- A period of the process (before / after a change) given its own limits.
- Pp, Ppk
- Like Cp and Cpk but with the overall sigma: long-term performance.
- PPAP
- Production part approval process (automotive).
- Pre-control
- Green / yellow / red zones from the tolerance with simple run or stop rules.
- Range
- Largest minus smallest value in a group.
- Rational subgroup
- A small group of parts made under the same conditions.
- Regression
- A model of how a result changes with one or more inputs.
- Repeatability
- Variation when one person measures the same part several times with one gauge.
- Reproducibility
- Variation between different people measuring the same parts.
- RTY
- Rolled throughput yield: product of the first pass yields of all steps.
- Run chart
- Readings plotted in time order around the median.
- R²
- The share of the variation in a result explained by a regression model.
- Sigma (σ)
- The standard deviation; also used for the sigma level of a process.
- Sigma level
- How many standard deviations fit between the mean and the nearer limit.
- SIPOC
- Suppliers, Inputs, Process, Outputs, Customers.
- Special cause
- A specific event outside the normal process: worn tool, new lot, wrong setting.
- Specification (tolerance)
- The range of acceptable values set by the design.
- Standard deviation
- The typical distance of readings from their mean.
- Subgroup
- A small group of readings taken together and charted as one point.
- Takt time
- Available time divided by customer demand.
- VOC
- Voice of the customer.
- Weibull
- A flexible distribution for life data; its shape tells early-life, random or wear-out failure.
- Within / overall sigma
- Short-term spread (from ranges) and total spread (plain standard deviation).
- Xbar-R / Xbar-S chart
- Charts of subgroup means with their ranges or standard deviations.
- Z-score
- How many standard deviations a value is from the mean.
- Zones A, B, C
- Bands 2-3, 1-2 and 0-1 sigma from the center line, used by the pattern rules.
